Log in. About Us. Gift Cards. Cookie Policy. Help Sign In Cart 0. Customize It! Refillable Butane Rechargeable Electric. Rechargeable Refillable Gaming. Fire Starters Lanterns.
Fuel-Flints-Wicks Pouches Displays. Sunglasses Reading. Privacy Policy Outside U. There are many videos online which show you how to do this. If the lighter does not spark, make sure there is a flint in it.
Take the lighter insert out and unscrew the spring on the bottom. Take the spring out, and tip the insert upside down, being careful not to lose the flint if there is one in it. If there is no flint, put a replacement flint in the tube, and screw the spring back in. If there is a flint, the you could put another flint behind it or stretch the spring slightly to increase the pressure on the striker wheel. You could also try cleaning the striker wheel with lighter fluid and a brass bristle brush as debris can collect over time.
If the lighter still fails to spark, then the striker wheel could have been worn down. This can occur in old lighters, as I have a vintage brass lighter where this has occurred. If this is the case, you will need to follow the instructions on their website and send it back, they will repair it for free. You can buy lighter fluid, replacement flints, and wicks from most corner shops, or they are very cheap online. Firstly you will need a can of petroleum for lighters, such as Zippo's own.
Then open the Zippo lighter, and remove the inner which contains the spark and wick. At the bottom you will see some felt-type substance, and a brass screw.
Using either your finger nails or tweezers, lift the felting. Then taking your petrol, carefully insert the nozzle under the felting, and squeeze the can twice to ensure petrol goes into the body of the lighter. Be careful not to overfill. Replace the inner of the lighter back inside the casing. Oh my goodness… Your question is the proverbial blast from the past. It was the perfect part-time job for kids who loved cars.
Of course, we all smoked back then; as did many people. And most of us had Zippo lighters. The residual fuel in the hose was a perfect fill. And it worked quite well. However, we were foolish, of course.
I would not recommend it. Go out and buy yourself a can of Ronson lighter fluid. Pull the insert and turn it upside down. Fold back the thick pad and apply fluid to the cotton wadding. Replace insert into the case and wipe up any spilled or excess fluid. You may notice a small puddle of fluid I missed while cleaning up. The video also shows that immediately after refilling the lighter, it wouldn't light.
You need spark, fuel and oxygen to produce fire, too high a concentration of fuel vapor will deprive your lighter of oxygen. Blow it out or let it air out and disperse. Make sure to vent it in a well ventilated area, generally outdoors is a good idea.
You should use a small screwdriver or the tip of a knife to press down on the small bit in the centre. The inside of the lighter slides out of the case. Just grab the windscreen and pull up firmly. The inside of the lighter is stuffed full of cotton and covered with a piece of felt. Pry up the felt and saturate the cotton with lighter fluid.
There's also a brass screw on the bottom that holds the "flint" in place with a spring. Not hard at all. Simply tug out the insert, invert it so that the bottom is on top and apply your fuel. Some not all Zippos feature a small hole in the center of the reservoir's felt cover. Supposedly, this is a niche for an extra flint. I usually use this hole to help refill and I simply keep spare flints under the felt. When the felt cover appears saturated with fuel: Stop fueling.
If you overfill, just keep holding your Zippo upside-down and let some of the excess fuel drip away from the wick. Once it stops dripping, reassemble the lighter and cautiously ignite it; letting it burn for around seconds to use up some of the excess.
Although the danger from overfilling is marginal - it could cause a large flash upon lighting - should any excess fuel leak out while the lighter is in a shirt or trouser pocket, you may feel some irritation chemical burning.
Take precautions by carrying your lighter elsewhere. Related searches to item repair zippo zippo lighter repair near me. Create this form in 5 minutes! How to create an eSignature for the Zippo Lighter Repair Form online zippo repair ukone-size-fits-all solution to eSign zippo repair form?
All you need is smooth internet connection and a device to work on. Follow the step-by-step instructions below to eSign your zippo warranty: Select the document you want to sign and click Upload. Choose My Signature. Decide on what kind of eSignature to create. Zippo Lighters does not warrant its products against normal wear or misuse. Products are not intended to be used as hammers, chisels, pry bars, or screwdrivers.
If your knife or other item was damaged due to misuse, our repair department can analyze the damage and repair it for a reasonable fee. If you have a warranty issue or questions about the condition of your Zippo Lighters product, please contact us and we will advise you on how best to proceed with submitting your warranty claim to the manufacturer.
0コメント